dangerdate7

Peugeot 208 Key Replacement It is recommended to leave the replacement of Peugeot keys for 208 to auto locksmiths who have the required equipment and know-how. They will be able to create and program new keys much faster than a dealership would and at a lesser cost. If the key fob stopped locking or unlocking your doors it could be due to a dead coin battery. But, there are other possibilities that the key is malfunctioning. Dead Coin Battery A dead battery in the coin compartment will hinder your Peugeot 208 from locking or unlocking, and won't start the engine. In this case you'll need to make use of the alternative method for starting that is described in the owner's manual. The spark plugs might also be worn out. The spark plugs are responsible for igniting the fuel that ignites the engine. However they have a finite time of life. If they are not used enough to last, they'll eventually fail. Fortunately, there's an easy solution to this problem. peugeot key to solve this issue is to check the voltage of your car battery using a multimeter. If it's less than 11.5 Volts it is time to replace it. It is also necessary to clean the battery's contacts in the event that it is damaged by corrosion. This can be accomplished by removing the rubber cover from the two battery terminals and then using a wirebrush to remove any corroded battery parts. Then, reconnect your cables to connect the positive and negative poles. Water Damage If your 208 isn't starting and the battery is not flat then you should check whether the spark plugs work. You may find that they're dirty and they don't spark. The spark plugs can be cleaned in the workshop. Peugeot cars use keys that are transponder-type and integrates with the car's immobiliser system. This ensures that only a valid key is able to turn the engine. If the chip in the Peugeot key is damaged, it will not send the correct signal to the vehicle. Water damage is a common cause of this issue. This is especially prevalent in colder climates where the vehicle could have been exposed to snow or rain. In this case, contact a trusted locksmith who will have the required tools and equipment to modify the key. They also have the latest technology and equipment needed to create the Peugeot 208 smart key. The process shouldn't last more than 15 minutes. Contacts to the battery are not working properly. Peugeot changed from the carbon-encased transponder chips to an entirely new type of chip that incorporates electronic components on circuit boards. The new system works great in its initial state, but the circuit boards degrade over time and stop working properly. This could stop the immobiliser chip activating the immobiliser chip, causing your car not to start. If this is the case it's a good idea to call a Peugeot specialist or locksmith. A common issue occurs when the battery of the key fob begins to die. This causes the blade of the key to stop feeding into the lock. A locksmith for cars will replace the battery and then cut a fresh blade for you. This is a simple solution. Faulty Receiver Module It could be that the receiver module has a problem If your Peugeot key fob doesn't work after being dropped on the floor, exposed to a sudden storm or accidentally washed. The receiver module is responsible for transmitting radio frequency to the onboard computer that regulates the central locking system of your Peugeot vehicle. Rubber seals on the key fob keep water from reaching its electronic chip. However prolonged exposure to water can be able to penetrate these seals and cause damage to the chip. The high salt content in the pool or ocean waters can cause damage to the key fob if it is submerged. If your Peugeot spare key fob stops working You'll need the module replaced. This should be done by a Peugeot specialist or an expert auto locksmith. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the right programming to allow the car to start. This is the reason that you should only trust the Peugeot locksmith to design and program the replacement. Computer malfunctioning on-board The on-board computer in your Peugeot is responsible many systems inside your car, including power windows and airbags. The computer on board will display an error code when something goes wrong. The code will be stored in the system until the problem is resolved. Usually, this will mean replacing the on-board computer. One of the most common causes of the airbag light flashing is loose or corroded connection in the airbag sensor. This could be due to wear and tear, ageing, or exposure to moisture and salt. It is imperative to have this issue addressed as quickly as you can, since the airbag malfunctioning could be dangerous in the event of an accident. If your Peugeot is showing a card not detected error, the battery inside the key fob may be weak or dead. This will stop the key fob from sending a signal to deactivate the immobilizer in your vehicle. Try this by pressing the unlock key on the key fob, and then trying to start your vehicle. If this doesn't work, the key battery needs to be replaced.